ppm-series ? ppm10-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 ppm10-e-xxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications input voltage range 85 ? 264 vac or 120 ? 370 vdc universal input frequency 47 ? 440 hz 110 vac 230 vac input (inrush) current 230 ma (10a), typ. 150ma (20a), typ. external input fuse (recommended) 2a / 250v slow blow output specifications voltage accuracy 2%, typ (3% at 3.3 vout) input variation 0.5%, typ load variation (10-100%) 1% , typ ripple and noise (20mhz bandwidth) 50mv pk-pk, typ short circuit protection continuous, auto resume over current protection > 110% io common specifications temperature range -25c to +70 c power derating 2% / c case temperature +95c (max) storage -40c to +105 c hold up time 50ms, typ. (230vac) humidity (non condensing) 95%, max. temperature coefficient 0.02%/c switching frequency 60khz, typ i/o isolation voltage 4000vac / 1min. leakage current 0.1ma, typ emi / rfi conducted en55011, level b emc compliance esd ie c/en 61000-4-2 15kv/8kv rf iec/en 61000-4-3 10v/m eft / bursts iec/en 61000-4-4 4 kv surge iec/en 61000-4-5 2kv/4kv safety standards iec60601, en60601, ul60950 safety approvals en60601, ul60950 (pending) safety class class 2 case material ul94v-0 rated reliability calculated mtbf (mil-hdbk-217f) > 300,000 hrs weight ~ 50g mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the ppm - series are high efficiency green power moduls with various packaging provided by peak. the features of this se ries are: wide input voltage, dc and ac all in one, high efficiency, hig h reliability, low loss, safety isolation etc. they are widely used in indus trial, office and civil equipments.. ppm-series 10 watt univ. 85-264vac (120-370vdc) single output over voltage protection (out) 4 kv ac i/o isolation low ripple and noise high efficiency rev.04-2012
ppm-series ? ppm10-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # p o w e r ( w ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) single output ppm10-e-3r3elf 6.6 3.3 2000 70 PPM10-E-05ELF 10 5 2000 74 ppm10-e-09elf 10 9 1100 76 ppm10-e-12elf 10 12 900 76 ppm10-e-15elf 10 15 700 78 ppm10-e-24elf 10 24 450 80 if you need other specifications, please enquire. package / pinning / derating all dimensions are typical in millimeters (inches). - pin diameter: 1.0 +/-0.10 (0.04 +/-0.004) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. modelcode datecode 19.00 (0.75) 2" x 1" C plastic case 2 4 1 3 45.72 (1.80) 6.00 (0.24) pe a k 53.50 (2.10) bottom view # single 1 ac (n) 2 ac (l) 3 + vout 4 - vout pin connections
ppm-series ? ppm10-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 app notes: measure typical applications ppm-series figure 1 figure 2 external typical value model c1 c2 tvs ppm10-e-3.3elf 220f/10v 0.1f/50v p6ke6.8a PPM10-E-05ELF 220f/10v 0.1f/50v p6ke6.8a ppm10-e-09elf 120f/25v 0.1f/50v p6ke12a ppm10-e-12elf 120f/25v 0.1f/50v p6ke20a ppm10-e-15elf 120f/25v 0.1f/50v p6ke20a ppm10-e-24elf 68f/35v 0.1f/50v p6ke30a note 1. output filtering capacitors c1 is electrolytic c apacitors. it is recommended to use high frequency and low impedance electrolytic capacitors. for capacitance and current of capacitor, please refer to manufactu re?s datasheet. voltage derating of capacitor should be 80% or above. c2 is ceramic capacitor - it is used to filter high frequency noise. tvs is a recommended c omponent to protect post-circuits (if converter fai ls). 2. mov is required for ppm10-e-xxelf models. model 471kd05 is used to protect the device under surge. 3. it is recommended to connect fuse (2a/250v slow blow). external input ntc model is recommended to use (5d-9). 4. if common requirement to emc performance, refer to figure 1, if higher requirement to emc performan ce, refer to figure 2. c3,c4:y capacitor, recommended parameter 2200 pf/400v; c5:x capacitor, recommended parameter 0.1uf/2 75v; nf: common model choke, recommended inductance i s about 10mh-30mh.
|